Vertex Learn

Level 1 Physics, Earth and Space Science (energy) practice paper 2026

Question One

Question One

a
Achieved

A luge track runs down a hill in Rotorua. A rider sits in a luge cart at the top of the track. The cart starts from rest and rolls all the way down the track to the bottom, with no motor.

(i) Describe the energy changes as the cart rolls from the top of the track to the bottom.

(ii) State the law of conservation of energy.

Hint

At the top the cart is high but not moving. At the bottom it is low and moving. Rubbing and noise also take some energy.

Answer

(i) At the top the cart and rider have gravitational potential energy (Ep). As they roll down, Ep is transformed into kinetic energy (Ek), so the cart speeds up. Some energy is transformed into thermal energy (heat) by friction between the wheels and the track and by air resistance, and some into sound. (ii) Energy cannot be created or destroyed; it can only be transformed from one form to another or transferred from one object to another, so the total energy stays the same.

Step by step
  1. Gravitational potential energy (Ep) is energy an object has because of its height. At the top of the track the cart is at its highest, so it has the most Ep.
  2. Kinetic energy (Ek) is energy of movement. At the top the cart is at rest, so it has no Ek yet.
  3. As the cart rolls down, it loses height, so it loses Ep. It speeds up, so it gains Ek.
  4. The track is not perfectly smooth and the cart pushes through air. Friction and air resistance turn some of the energy into thermal energy (heat) in the wheels, track and air.
  5. The wheels rumbling on the track also make sound, which carries some energy away.
  6. (ii) Conservation of energy: energy is never made or destroyed. It only changes form or moves to something else. So Ep at the top = Ek + thermal energy + sound energy at the bottom.
Full working
  1. top: Ep greatest, Ek = 0high and at rest
  2. rolling down: Ep → Ekloses height, gains speed
  3. some Ep → thermal energy and soundfriction, air resistance
  4. energy is not created or destroyed, only transformed or transferredconservation of energy
  5. Ep → Ek + thermal + sound; total energy stays the same
b
Merit

A luge track runs down a hill in Rotorua. The top of the track is 25 m higher than the bottom. A chairlift carries the rider and the luge cart from the bottom back up to the top. The rider and cart have a total mass of 90 kg, and the chairlift takes 75 s to lift them.

Use g = 10 N kg⁻¹, Ep = mgh and P = E ÷ t (from E = Pt).

(i) Calculate the gravitational potential energy gained by the rider and cart.

(ii) Calculate the power needed to give them this energy in 75 s.

(iii) The chairlift motor uses much more power than your answer to (ii) for each rider it carries. Explain why.

Hint

Ep = mgh with m = 90 kg, g = 10 N kg⁻¹ and h = 25 m. Power is energy divided by time. Then think about what else the motor has to lift and where energy is wasted.

Answer

(i) Ep = mgh = 90 × 10 × 25 = 22 500 J. (ii) P = E ÷ t = 22 500 ÷ 75 = 300 W. (iii) The motor also has to lift the chair itself, which gains Ep too, and not all the electrical energy it uses becomes Ep. Some is transformed into thermal energy (heat) by friction in the motor, the pulleys and the moving cable, and some into sound. So the motor needs more than 300 W of electrical power for each rider.

Step by step
  1. (i) Use Ep = mgh. The mass is 90 kg, g is 10 N kg⁻¹ and the height gained is 25 m.
  2. Ep = 90 × 10 × 25 = 22 500 J.
  3. (ii) Power is how fast energy is transferred. From E = Pt, P = E ÷ t.
  4. P = 22 500 ÷ 75 = 300 W. That is 300 joules every second.
  5. (iii) 300 W is only the useful energy going into the rider and cart each second.
  6. The motor also lifts the chair, which has its own mass, so the chair gains Ep as well.
  7. Friction in the motor, the pulleys and the cable turns some electrical energy into thermal energy, and the machinery makes sound.
  8. This energy does not become Ep of the rider, so the motor must use more than 300 W. Energy is still conserved; it just ends up in other forms.
Full working
  1. Ep = mgh = 90 × 10 × 25m = 90 kg, h = 25 m
  2. Ep = 22 500 J
  3. P = E ÷ t = 22 500 ÷ 75from E = Pt
  4. P = 300 Wuseful power for one rider
  5. motor also lifts the chair; friction → thermal energy and soundwhy more power is used
  6. Ep = 22 500 J; P = 300 W; the motor uses more because of the chair's Ep and energy lost as heat and sound
c
Excellence

A luge track runs down a hill in Rotorua. The top of the track is 25 m higher than the bottom and the track is 400 m long. The rider and cart have a total mass of 90 kg. The cart starts from rest at the top and rolls down with no braking. At the bottom its speed is measured as 12.0 m s⁻¹.

Use g = 10 N kg⁻¹, Ep = mgh, Ek = (12)mv² and W = Fd.

Discuss the energy of the cart and rider as they roll down the track.

In your answer, you should:

• calculate the greatest speed the cart could have at the bottom, and state the assumption you made

• calculate the kinetic energy the cart actually has at the bottom

• calculate how much energy was transformed into other forms, and the average force resisting the motion over the 400 m track

• explain why the cart does not reach the greatest speed.

Hint

If no energy is lost, all the Ep becomes Ek, so mgh = (12)mv². The difference between the Ep at the top and the real Ek at the bottom is the energy that went into heat and sound. That energy was the work done against friction, W = Fd.

Answer

Ep at the top = mgh = 90 × 10 × 25 = 22 500 J. If no energy is lost to friction or air resistance (all Ep becomes Ek), then (12) × 90 × v² = 22 500, so v² = 500 and v = 22.4 m s⁻¹. The actual Ek at the bottom = (12) × 90 × 12.0² = 6480 J. So 22 500 − 6480 = 16 020 J (about 71%) was transformed into thermal energy and sound. This is the work done against friction and air resistance: F = W ÷ d = 16 020 ÷ 400 = 40 N (40.05 N). The cart does not reach 22.4 m s⁻¹ because friction between the wheels and the track and air resistance act against its motion the whole way down. Air particles hit the front of the cart and rider, and the wheels rub on the track, so the particles of the wheels, track and air move faster and warm up. Energy is conserved, but only 6480 J of the 22 500 J (28.8%) is still kinetic energy at the bottom, so the cart is much slower.

Step by step
  1. Start with the energy at the top: Ep = mgh = 90 × 10 × 25 = 22 500 J. The cart starts at rest, so Ek = 0.
  2. Greatest speed: assume no energy is lost to friction, air resistance or sound, so all 22 500 J of Ep becomes Ek at the bottom.
  3. Ek = (12)mv², so 22 500 = (12) × 90 × v² = 45v².
  4. v² = 22 500 ÷ 45 = 500, so v = √500 = 22.4 m s⁻¹. Remember to take the square root.
  5. Actual Ek at the bottom: (12) × 90 × 12.0² = 45 × 144 = 6480 J.
  6. Energy transformed into other forms: 22 500 − 6480 = 16 020 J. This went into thermal energy (heat) and sound.
  7. That energy was used to do work against friction and air resistance over the 400 m. W = Fd, so F = W ÷ d = 16 020 ÷ 400 = 40 N (to 2 significant figures).
  8. Why slower: friction where the wheels and axles rub, and air particles hitting the front of the cart, act against the motion all the way down. They turn kinetic energy into thermal energy in the wheels, track and air, plus some sound.
  9. Only 6480 ÷ 22 500 = 28.8% of the starting energy is still kinetic energy at the bottom. Energy is not destroyed; it has been transformed into forms that do not move the cart.
  10. So the real speed (12.0 m s⁻¹) is a lot less than the no-loss speed (22.4 m s⁻¹).
Full working
  1. Ep = mgh = 90 × 10 × 25 = 22 500 Jenergy at the top
  2. assume all Ep → Ek (no friction or air resistance)assumption
  3. 22 500 = (12) × 90 × v², so v² = 500mgh = (12)mv²
  4. v = √500 = 22.4 m s⁻¹greatest speed
  5. Ek = (12) × 90 × 12.0² = 6480 Jactual Ek at the bottom
  6. 22 500 − 6480 = 16 020 Jtransformed into heat and sound
  7. F = W ÷ d = 16 020 ÷ 400 = 40 NW = Fd
  8. 6480 ÷ 22 500 × 100 = 28.8%share still kinetic
  9. Greatest speed 22.4 m s⁻¹; actual Ek 6480 J; 16 020 J to heat and sound; average resistive force about 40 N
d
Excellence

At the bottom of a luge track in Rotorua there is a flat run-out where riders brake to a stop. A rider and cart with a total mass of 90 kg arrive at the run-out at 12.0 m s⁻¹. The rider pulls the brake and the cart stops in 8.0 m.

Use Ek = (12)mv² and W = Fd.

Discuss the energy transfers as the cart brakes, and what this means for a faster rider.

In your answer, you should:

• calculate the average braking force on the cart

• describe where the cart's kinetic energy goes

• calculate the stopping distance for a 90 kg rider and cart arriving at 18.0 m s⁻¹ with the same braking force

• explain why the stopping distance increases by more than the speed does, and what this means for the length of the run-out.

Hint

The brakes do work on the cart until all its kinetic energy is gone, so W = Ek and F = Ek ÷ d. For the faster rider, find the new Ek first. Speed is squared in Ek = (12)mv².

Answer

At 12.0 m s⁻¹, Ek = (12) × 90 × 12.0² = 6480 J. The brakes do work equal to this Ek, so F = W ÷ d = 6480 ÷ 8.0 = 810 N. The kinetic energy is transformed into thermal energy (heat) in the brake pads, the wheels and the track, because friction makes their particles vibrate faster, and a little into sound. At 18.0 m s⁻¹, Ek = (12) × 90 × 18.0² = 14 580 J, so with the same 810 N force d = 14 580 ÷ 810 = 18 m. The speed is only 1.5 times bigger, but Ek depends on v², so the Ek is 1.5² = 2.25 times bigger, and so is the stopping distance (8.0 m × 2.25 = 18 m). The run-out must be long enough for the fastest riders, more than twice as long as for a rider at 12.0 m s⁻¹, and the brakes get hotter because they must turn more than twice as much energy into heat.

Step by step
  1. Work out the cart's kinetic energy at 12.0 m s⁻¹: Ek = (12) × 90 × 12.0² = 45 × 144 = 6480 J.
  2. To stop the cart, the brakes must remove all this kinetic energy. The energy they remove is the work done: W = Fd.
  3. So F = W ÷ d = 6480 ÷ 8.0 = 810 N. This is the average braking force.
  4. Where the energy goes: friction between the brake and the wheel, and between the wheels and the track, makes their particles vibrate faster, so they warm up. The kinetic energy becomes thermal energy (heat), plus a little sound.
  5. Faster rider at 18.0 m s⁻¹: Ek = (12) × 90 × 18.0² = 45 × 324 = 14 580 J.
  6. Same braking force, so d = W ÷ F = 14 580 ÷ 810 = 18 m.
  7. Why so much longer: 18.0 is 1.5 times 12.0, but Ek depends on speed squared, so Ek grows by 1.5² = 2.25 times.
  8. With the same force, the brakes need 2.25 times the distance to remove 2.25 times the energy: 8.0 × 2.25 = 18 m.
  9. Meaning: the run-out must be designed for the fastest riders, and the brakes heat up more. A small rise in speed needs a much longer stopping distance.
Full working
  1. Ek = (12) × 90 × 12.0² = 6480 Jat 12.0 m s⁻¹
  2. W = Ek = 6480 Jbrakes remove all the Ek
  3. F = W ÷ d = 6480 ÷ 8.0 = 810 Naverage braking force
  4. Ek → thermal energy (brakes, wheels, track) + soundfriction
  5. Ek = (12) × 90 × 18.0² = 14 580 Jat 18.0 m s⁻¹
  6. d = W ÷ F = 14 580 ÷ 810 = 18 msame braking force
  7. (18.0 ÷ 12.0)² = 1.5² = 2.25Ek depends on v²
  8. F = 810 N; stopping distance 18 m, 2.25 times longer because Ek depends on v²
Question Two

Question Two

a
Achieved

A family in Invercargill has two kinds of light bulb in their house: an old filament bulb rated 60 W and an LED bulb rated 8 W. Both give about the same amount of light.

(i) Describe the energy changes in each bulb when it is switched on.

(ii) State what the power rating of 60 W tells you about the filament bulb.

Hint

Both bulbs take in electrical energy. Ask which forms of energy come out. Power is energy per second.

Answer

(i) In both bulbs electrical energy is transformed into light energy and thermal energy (heat). The filament bulb transforms most of its electrical energy into thermal energy, which is why it gets very hot; the LED transforms a much bigger share into light and stays only warm. (ii) 60 W means the filament bulb transforms 60 joules of electrical energy into other forms every second.

Step by step
  1. Both bulbs get electrical energy from the circuit.
  2. Both give out light energy, which is the useful energy.
  3. Both also give out thermal energy (heat), which is wasted energy for a light bulb.
  4. The filament bulb gets so hot you cannot touch it, because most of its energy becomes heat. The LED only gets warm, because more of its energy becomes light.
  5. (ii) Power is the rate of energy transfer. 1 watt = 1 joule per second, so 60 W means 60 J of electrical energy is transformed every second.
Full working
  1. electrical energy → light energy + thermal energyboth bulbs
  2. filament bulb: mostly thermal energygets very hot
  3. LED: more light, less thermal energystays warm
  4. 1 W = 1 J each secondpower is the rate of energy transfer
  5. Electrical → light + heat in both; 60 W means 60 J transformed each second
b
Merit

A heater in a house in Invercargill is plugged into the 240 V mains supply. On its high setting it has a power of 2400 W.

Use P = VI and V = IR.

Calculate the current in the heater and the resistance of its heating element on the high setting.

Include the correct units.

Hint

Rearrange P = VI to get I = P ÷ V. Then rearrange V = IR to get R = V ÷ I.

Answer

I = P ÷ V = 2400 ÷ 240 = 10 A. R = V ÷ I = 240 ÷ 10 = 24 Ω.

Step by step
  1. Write down what you know: P = 2400 W and V = 240 V.
  2. Power, voltage and current are linked by P = VI. Divide both sides by V to get I = P ÷ V.
  3. I = 2400 ÷ 240 = 10 A. Current is measured in amperes (A).
  4. Now use V = IR. Divide both sides by I to get R = V ÷ I.
  5. R = 240 ÷ 10 = 24 Ω. Resistance is measured in ohms (Ω).
Full working
  1. P = VI, so I = P ÷ Vrearrange
  2. I = 2400 ÷ 240 = 10 A
  3. V = IR, so R = V ÷ Irearrange
  4. R = 240 ÷ 10 = 24 Ω
  5. I = 10 A, R = 24 Ω
c
Excellence

A family in Invercargill is choosing between a 60 W filament bulb and an 8 W LED bulb for the lounge. Both give out about 5 W of light. The lounge light is on for 5 hours every evening for the 90 days of winter. Electricity costs $0.34 per kWh.

Use E = Pt (with P in kW and t in hours, E is in kWh).

Discuss which bulb the family should choose.

In your answer, you should:

• calculate the energy each bulb uses over the winter, in kWh

• calculate the cost of running each bulb over the winter, and the money saved by the LED

• calculate the efficiency of each bulb

• explain, using energy transformations, why the LED uses less energy for the same light.

Hint

Total time = 5 × 90 hours. Change watts to kilowatts by dividing by 1000. Efficiency = (useful energy out) ÷ (energy in) × 100%, and here the useful output is the 5 W of light.

Answer

Time on = 5 × 90 = 450 h. Filament: E = Pt = 0.060 kW × 450 h = 27 kWh, costing 27 × $0.34 = $9.18. LED: E = 0.008 kW × 450 h = 3.6 kWh, costing 3.6 × $0.34 = $1.22. The LED saves $7.96 over the winter. Efficiency: filament = 5 ÷ 60 × 100% = 8.3%; LED = 5 ÷ 8 × 100% = 62.5%. Both bulbs transform electrical energy into light and thermal energy. The filament bulb makes light by heating a thin wire until it glows, so about 55 J of every 60 J becomes wasted heat. The LED makes light directly and wastes only about 3 J of every 8 J as heat. Both give the same 5 J of light each second, so the LED needs far less electrical energy for the same useful output. The family should choose the LED: it uses 23.4 kWh less energy and costs less to run (and it lasts longer).

Step by step
  1. Total time the light is on: 5 hours × 90 days = 450 hours.
  2. Change the powers to kilowatts: 60 W = 0.060 kW and 8 W = 0.008 kW.
  3. Filament bulb: E = Pt = 0.060 × 450 = 27 kWh.
  4. LED: E = 0.008 × 450 = 3.6 kWh.
  5. Cost = energy in kWh × price. Filament: 27 × 0.34 = $9.18. LED: 3.6 × 0.34 = $1.224, so $1.22.
  6. Saving: 9.18 − 1.22 = $7.96 over one winter, for one bulb.
  7. Efficiency = (useful energy out) ÷ (energy in) × 100%. The useful output is light, 5 W for both.
  8. Filament: 5 ÷ 60 × 100% = 8.3%. LED: 5 ÷ 8 × 100% = 62.5%.
  9. Why: both bulbs turn electrical energy into light and heat. The filament bulb heats a thin wire until it glows, so most of its energy (55 W of the 60 W) is wasted as heat.
  10. The LED turns a much bigger share of its electrical energy straight into light, and only 3 W of its 8 W becomes heat.
  11. Both give the same light, so the LED needs much less electrical energy each second. Less energy used means a lower power bill. The LED is the better choice.
Full working
  1. t = 5 × 90 = 450 htime switched on
  2. filament: E = 0.060 kW × 450 h = 27 kWhE = Pt
  3. LED: E = 0.008 kW × 450 h = 3.6 kWhE = Pt
  4. filament cost = 27 × $0.34 = $9.18energy × price
  5. LED cost = 3.6 × $0.34 = $1.22energy × price
  6. saving = $9.18 − $1.22 = $7.96
  7. filament efficiency = 5 ÷ 60 × 100% = 8.3%useful light 5 W
  8. LED efficiency = 5 ÷ 8 × 100% = 62.5%
  9. filament wastes 55 W as heat; LED wastes 3 Welectrical → light + heat
  10. Choose the LED: 3.6 kWh ($1.22) against 27 kWh ($9.18), saving $7.96; efficiency 62.5% against 8.3%
d
Excellence

A heater in a house in Invercargill runs on the 240 V mains supply. On its high setting the heating element has a resistance of 24 Ω. When the heater is switched to its low setting, the resistance of the element changes to 48 Ω. The voltage stays at 240 V.

Use V = IR, P = VI and E = Pt.

Discuss how switching from the high setting to the low setting changes the thermal energy released by the heater in 2 hours.

In your answer, you should:

• calculate the current and the power on each setting

• calculate the thermal energy released in 2 hours on each setting

• explain, using the formulae, why doubling the resistance changes the thermal energy in this way.

Hint

I = V ÷ R. Then P = VI. Then E = Pt with t in seconds: 2 h = 2 × 60 × 60 s. Keep track of which quantity stays the same.

Answer

High: I = V ÷ R = 240 ÷ 24 = 10 A, P = VI = 240 × 10 = 2400 W, E = Pt = 2400 × 7200 = 17 280 000 J (17.28 MJ, 4.8 kWh). Low: I = 240 ÷ 48 = 5 A, P = 240 × 5 = 1200 W, E = 1200 × 7200 = 8 640 000 J (8.64 MJ, 2.4 kWh). Doubling the resistance with the voltage fixed halves the current (I = V ÷ R). With V the same and I halved, the power halves (P = VI), so electrical energy is transformed into thermal energy at half the rate. In the same 2 hours the thermal energy released halves (E = Pt), so the room warms more slowly but the heater also costs half as much to run.

Step by step
  1. The supply voltage stays at 240 V on both settings. Only the resistance changes.
  2. High setting: I = V ÷ R = 240 ÷ 24 = 10 A. P = VI = 240 × 10 = 2400 W.
  3. Low setting: I = 240 ÷ 48 = 5 A. P = 240 × 5 = 1200 W.
  4. Time in seconds: 2 h = 2 × 60 × 60 = 7200 s.
  5. High: E = Pt = 2400 × 7200 = 17 280 000 J (17.28 MJ).
  6. Low: E = 1200 × 7200 = 8 640 000 J (8.64 MJ).
  7. Why: resistance opposes the current. With twice the resistance and the same voltage, I = V ÷ R gives half the current.
  8. P = VI. V stays the same and I halves, so the power halves. Power is how fast electrical energy becomes thermal energy, so heat is released at half the rate.
  9. E = Pt. The time is the same 2 hours and P halves, so the thermal energy released halves.
  10. Result: on low the room warms more slowly, but the heater uses half the electrical energy, so it costs half as much to run.
Full working
  1. high: I = 240 ÷ 24 = 10 AI = V ÷ R
  2. high: P = 240 × 10 = 2400 WP = VI
  3. low: I = 240 ÷ 48 = 5 AI = V ÷ R
  4. low: P = 240 × 5 = 1200 WP = VI
  5. t = 2 × 60 × 60 = 7200 s
  6. high: E = 2400 × 7200 = 17 280 000 JE = Pt
  7. low: E = 1200 × 7200 = 8 640 000 JE = Pt
  8. R doubles, V fixed → I halves → P halves → E halves in the same time
  9. High 17.28 MJ, low 8.64 MJ: doubling R halves I, P and the thermal energy released
Question Three

Question Three

a
Achieved

A student takes ice cubes from a freezer and leaves them in a bowl in a warm kitchen. The ice warms up to 0 °C and then melts. While the ice is melting, its temperature stays at 0 °C.

(i) State what is meant by the specific latent heat of fusion of a substance.

(ii) Describe what happens to the particles of ice as it melts, and why the temperature stays at 0 °C while it melts.

Hint

Latent heat is the energy for a change of state, not for a change of temperature. Think about what holds the particles of a solid in place.

Answer

(i) The specific latent heat of fusion is the energy needed to change 1 kg of a substance from solid to liquid without changing its temperature. (ii) In ice the particles are held in fixed positions by forces of attraction and vibrate in place. As the ice melts, the energy it takes in is used to break these bonds so the particles can move past each other as a liquid. The energy goes into breaking bonds, not into making the particles move faster, so their average kinetic energy, and so the temperature, stays at 0 °C until all the ice has melted.

Step by step
  1. (i) Fusion means melting. Latent heat is energy that changes the state of a substance without changing its temperature.
  2. Specific means for 1 kg. So the specific latent heat of fusion is the energy needed to melt 1 kg of the solid at its melting point.
  3. (ii) In ice the particles are close together in fixed positions. Forces of attraction (bonds) hold them in place, and they can only vibrate.
  4. When the ice melts, the energy it takes in from the kitchen breaks these bonds, so the particles can slide past each other. The solid becomes a liquid.
  5. Temperature measures the average kinetic energy of the particles. During melting the energy is used to break bonds, not to speed the particles up.
  6. So the temperature stays at 0 °C until all the ice has melted. Only then does the water start to warm up.
Full working
  1. latent heat of fusion = energy to melt 1 kg with no temperature changedefinition
  2. ice: particles in fixed positions, held by bonds, vibratingsolid
  3. energy taken in breaks bonds; particles move past each othermelting
  4. average kinetic energy unchangedtemperature stays at 0 °C
  5. Energy melts 1 kg without a temperature change; during melting it breaks bonds, so the temperature stays at 0 °C
b
Merit

Tama fills an electric jug with 1.5 kg of tap water at 15 °C. The jug has a power of 2200 W. It takes 4 minutes 30 seconds for the water to reach 100 °C.

The specific heat capacity of water is 4200 J kg⁻¹ °C⁻¹.

Use E = mcΔT and E = Pt.

(i) Calculate the thermal energy gained by the water.

(ii) Calculate the electrical energy used by the jug.

(iii) Explain why your two answers are different.

Hint

ΔT is the change in temperature: 100 − 15. Change 4 minutes 30 seconds into seconds before using E = Pt.

Answer

(i) ΔT = 100 − 15 = 85 °C, so E = mcΔT = 1.5 × 4200 × 85 = 535 500 J. (ii) t = 4 × 60 + 30 = 270 s, so E = Pt = 2200 × 270 = 594 000 J. (iii) The jug uses 58 500 J more electrical energy than the water gains. Not all the electrical energy goes into the water: some heats the element, the jug's body and lid, and some is lost to the surrounding air by conduction, convection and radiation, and as water vapour and sound. So the water gains only about 90% of the electrical energy.

Step by step
  1. (i) The temperature change is ΔT = 100 − 15 = 85 °C.
  2. Use E = mcΔT: 1.5 × 4200 × 85 = 535 500 J.
  3. (ii) Change the time to seconds: 4 × 60 + 30 = 270 s.
  4. Use E = Pt: 2200 × 270 = 594 000 J.
  5. (iii) Difference: 594 000 − 535 500 = 58 500 J.
  6. Energy is conserved, so this 58 500 J did not disappear. It heated the element, the plastic body and the lid of the jug.
  7. The hot jug also loses heat to the air around it by conduction, convection and radiation, some water evaporates as steam, and the jug makes some sound.
  8. So only 535 500 ÷ 594 000 = about 90% of the electrical energy ends up in the water.
Full working
  1. ΔT = 100 − 15 = 85 °C
  2. E = mcΔT = 1.5 × 4200 × 85 = 535 500 Jthermal energy gained by the water
  3. t = 4 × 60 + 30 = 270 s
  4. E = Pt = 2200 × 270 = 594 000 Jelectrical energy used
  5. 594 000 − 535 500 = 58 500 Jheats the jug and the air, steam, sound
  6. Water gains 535 500 J; the jug uses 594 000 J; 58 500 J heats the jug and surroundings
c
Excellence

A student measures the specific latent heat of fusion of ice. The student puts 0.200 kg of crushed ice at −10.0 °C into a thin plastic cup in a room at 20 °C, puts a 100 W immersion heater in it, switches the heater on and stirs. The table shows the temperature readings.

The accepted value for the specific latent heat of fusion of ice is 334 000 J kg⁻¹.

Use E = Pt and E = mL.

Discuss the student's result.

In your answer, you should:

• use the table to find how long the ice took to melt, and explain how you can tell

• calculate the student's value for the specific latent heat of fusion of ice, with its unit

• compare it with the accepted value, and explain the difference using heat transfer between the cup and the room.

Time (s)02040100200300400500600640700760
Temperature (°C)−10.0−5.00.00.00.00.00.00.00.00.07.515.0
Hint

The ice is melting while the temperature stays at 0 °C. Find when that flat part starts and ends. The heater's energy in that time is E = Pt, and L = E ÷ m. Is the room warmer or colder than the ice?

Answer

The temperature stays at 0 °C from 40 s to 640 s, so the ice took 600 s to melt: the energy was breaking bonds between particles, not raising the temperature. The heater gave E = Pt = 100 × 600 = 60 000 J in that time, so L = E ÷ m = 60 000 ÷ 0.200 = 300 000 J kg⁻¹. This is about 10% lower than 334 000 J kg⁻¹. Melting 0.200 kg of ice really needs 0.200 × 334 000 = 66 800 J, so about 6800 J must have come from somewhere other than the heater. The room (20 °C) is warmer than the ice (0 °C), so heat flowed into the cup from the room: by conduction through the thin plastic, from warm air moving past the cup by convection, and by radiation. The student assumed all the energy came from the heater, so the calculated L is too low. Insulating the cup (for example a polystyrene cup with a lid) would cut this heat gain and give a value closer to 334 000 J kg⁻¹.

Step by step
  1. Look for the flat part of the data: the temperature stays at 0.0 °C from 40 s to 640 s.
  2. While the ice melts, the energy goes into breaking bonds between the particles, so the temperature does not change. So the flat part is the melting time: 640 − 40 = 600 s.
  3. Energy from the heater while melting: E = Pt = 100 × 600 = 60 000 J.
  4. E = mL, so L = E ÷ m = 60 000 ÷ 0.200 = 300 000 J kg⁻¹.
  5. Compare: 300 000 is lower than 334 000 by 34 000, about 10%.
  6. To melt 0.200 kg really takes 0.200 × 334 000 = 66 800 J. The heater gave only 60 000 J, so about 6800 J came from somewhere else.
  7. The room is at 20 °C and the ice is at 0 °C. Heat always flows from hot to cold, so the room was heating the cup as well.
  8. Conduction: the thin plastic cup lets heat through from the air outside. Convection: warm room air moves past the cup, cools and is replaced by more warm air. Radiation: the warm walls and air give off infrared that the cup absorbs.
  9. The student counted only the heater's energy, so the energy used in the calculation was too small and L came out too low.
  10. Fix: use an insulated cup (polystyrene) with a lid, or run a second cup without a heater to measure how much ice the room melts, and subtract it.
Full working
  1. temperature constant at 0 °C from 40 s to 640 sice melting
  2. t = 640 − 40 = 600 smelting time
  3. E = Pt = 100 × 600 = 60 000 Jheater energy while melting
  4. L = E ÷ m = 60 000 ÷ 0.200 = 300 000 J kg⁻¹from E = mL
  5. 0.200 × 334 000 = 66 800 J needed6800 J came from the room
  6. room 20 °C, ice 0 °C → heat flows in by conduction, convection, radiationvalue too low
  7. Melting took 600 s; L = 300 000 J kg⁻¹, about 10% low because the room also heated the ice
d
Excellence

A family takes a chilly bin to the beach at Mount Maunganui on a hot day. The chilly bin has thick polystyrene foam walls, a white outside and a lid that seals tightly. Heat leaks into the chilly bin at about 20 W.

They can cool the food with either 2.0 kg of ice packs at 0 °C or 2.0 kg of water at 0 °C. The food is safe while the inside of the chilly bin stays at or below 6 °C.

Specific heat capacity of water = 4200 J kg⁻¹ °C⁻¹. Specific latent heat of fusion of ice = 334 000 J kg⁻¹.

Use E = mcΔT, E = mL and E = Pt.

Discuss which choice keeps the food safe for longer, and how the chilly bin's design helps.

In your answer, you should:

• calculate the energy each choice can absorb before reaching 6 °C

• calculate how long each choice keeps the food at or below 6 °C

• explain why the ice packs last so much longer

• explain how the foam walls, the white outside and the tight lid reduce the heat flowing in.

Hint

The water only warms from 0 °C to 6 °C. The ice must first melt (E = mL), then the meltwater warms from 0 °C to 6 °C. Time = energy ÷ power.

Answer

Water: E = mcΔT = 2.0 × 4200 × 6 = 50 400 J. Ice packs: melting E = mL = 2.0 × 334 000 = 668 000 J, then warming the meltwater to 6 °C another 50 400 J, total 718 400 J. At 20 W: water lasts t = E ÷ P = 50 400 ÷ 20 = 2520 s (42 minutes); ice lasts 718 400 ÷ 20 = 35 920 s (about 10 hours), about 14 times longer. Ice packs take in a large amount of energy while they melt, because the energy breaks the bonds between particles, and their temperature stays at 0 °C the whole time. The water has no melting to do, so all the energy raises its temperature straight away. The foam is mostly trapped air, which is a poor conductor, and because the air is trapped in small pockets it cannot flow, so conduction and convection through the walls are small. The white outside reflects most of the Sun's radiation instead of absorbing it. The tight lid stops warm air flowing in and cold air flowing out (convection). Keeping the leak small means the ice lasts for the whole day, so the family should use the ice packs and keep the lid closed.

Step by step
  1. Water at 0 °C: it can only warm up to 6 °C, so E = mcΔT = 2.0 × 4200 × 6 = 50 400 J.
  2. Ice packs at 0 °C: first they melt. E = mL = 2.0 × 334 000 = 668 000 J.
  3. Then the meltwater warms from 0 °C to 6 °C: another 50 400 J. Total = 668 000 + 50 400 = 718 400 J.
  4. Time = energy ÷ power (from E = Pt). Water: 50 400 ÷ 20 = 2520 s = 42 minutes.
  5. Ice: 718 400 ÷ 20 = 35 920 s. Divide by 3600: about 10 hours.
  6. The ice lasts about 14 times longer (718 400 ÷ 50 400 = 14.3).
  7. Why: melting needs a lot of energy to break the bonds between particles, and the temperature stays at 0 °C until all the ice has melted. The water skips this step, so the heat warms it straight away.
  8. Foam walls: polystyrene is mostly trapped air. Air is a poor conductor because its particles are far apart, so conduction is slow. The air is trapped in tiny pockets, so it cannot circulate, which stops convection inside the walls.
  9. White outside: white surfaces reflect most of the Sun's radiation, so less is absorbed.
  10. Tight lid: stops warm beach air flowing in and cold air flowing out, which would be convection.
  11. Together these keep the heat leak small (about 20 W). A smaller power means a longer time for the same energy, so the ice packs last the whole day at the beach.
Full working
  1. water: E = 2.0 × 4200 × 6 = 50 400 JE = mcΔT, 0 °C to 6 °C
  2. ice: E = 2.0 × 334 000 = 668 000 JE = mL, melting
  3. ice total = 668 000 + 50 400 = 718 400 Jmelt, then warm to 6 °C
  4. water: t = 50 400 ÷ 20 = 2520 s = 42 mint = E ÷ P
  5. ice: t = 718 400 ÷ 20 = 35 920 s ≈ 10 ht = E ÷ P
  6. 718 400 ÷ 50 400 ≈ 14ice lasts about 14 times longer
  7. foam: trapped air limits conduction and convection; white: reflects radiation; lid: stops convection
  8. Ice packs: 718 400 J, about 10 h; water: 50 400 J, 42 min. Melting absorbs most of the energy

All NCEA Level 1 Science

A Vertex Academy practice paper, written from NZQA's 2026 assessment specification for AS 92047. It is not an NZQA paper. Grades use the 2025 exam's cut scores: 7, 13 and 19 out of 24 for Achieved, Merit and Excellence.