Vertex Learn

Level 3 Physics electrical systems practice paper 2026

Question One

Question One

a
Achieved

A 9.0 V battery with an internal resistance of 0.50 Ω is connected to a 4.0 Ω resistor.

Use ε = I(R + r) and V = IR.

Calculate the current and the terminal voltage of the battery.

Hint

The internal resistance is in series with the 4.0 Ω resistor.

Answer

I = 9.0 ÷ (4.0 + 0.50) = 2.0 A. Terminal voltage V = IR = 2.0 × 4.0 = 8.0 V.

Step by step
  1. Total resistance = 4.0 + 0.50 = 4.5 Ω.
  2. I = ε ÷ (R + r) = 9.0 ÷ 4.5 = 2.0 A.
  3. Terminal voltage = voltage across the 4.0 Ω resistor = 2.0 × 4.0 = 8.0 V (or 9.0 − 2.0 × 0.50).
Full working
  1. I = 9.0 ÷ (4.0 + 0.50) = 2.0 A
  2. V = 2.0 × 4.0 = 8.0 V
b
Achieved

The 9.0 V battery (internal resistance 0.50 Ω) delivers a current of 2.0 A.

Use P = I²R.

Calculate the power wasted inside the battery, and state what happens to that energy.

Hint

Use the internal resistance for R.

Answer

P = 2.0² × 0.50 = 2.0 W, which heats the battery.

Step by step
  1. P = I²r = 2.0² × 0.50 = 2.0 W.
  2. This energy is turned into heat inside the battery.
Full working
  1. P = I²r = 2.0² × 0.50
  2. P = 2.0 W, as heat in the battery
c
Merit

A car battery has an EMF of 12.6 V and an internal resistance of 0.020 Ω. When the driver starts the engine, the starter motor draws 150 A.

Use V = ε − Ir.

Calculate the battery's terminal voltage while the starter runs, and explain why the headlights dim while the engine is being started.

Hint

The headlights are connected across the battery's terminals.

Answer

V = 12.6 − 150 × 0.020 = 12.6 − 3.0 = 9.6 V. The headlights are in parallel with the starter, across the battery terminals. The huge starter current makes a large voltage drop (3.0 V) across the internal resistance, so the terminal voltage falls from about 12.6 V to 9.6 V. With less voltage across them the headlights draw less current and their power (P = V² ÷ R) falls, so they dim.

Step by step
  1. Lost volts: Ir = 150 × 0.020 = 3.0 V.
  2. Terminal voltage: V = ε − Ir = 12.6 − 3.0 = 9.6 V.
  3. The headlights are connected across the terminals, in parallel with the starter.
  4. The large starter current drops the terminal voltage, so the headlights get only 9.6 V.
  5. Less voltage means less current and less power in the headlights, so they glow less brightly.
Full working
  1. Ir = 150 × 0.020 = 3.0 V
  2. V = 12.6 − 3.0 = 9.6 V
  3. headlights across the terminalsless V, less P
d
Excellence

In the circuit in the diagram, a 6.0 V cell and a 3.0 V cell (both with negligible internal resistance) are joined by three resistors: R₁ = 2.0 Ω with the 6.0 V cell, R₂ = 4.0 Ω in the middle branch, and R₃ = 1.0 Ω with the 3.0 V cell.

Use Kirchhoff's laws.

Calculate the current in R₂, and the current in the 3.0 V cell. Explain what the direction of the current in the 3.0 V cell shows.

+6.0 VR₁ = 2.0 ΩR₂ = 4.0 Ω+3.0 VR₃ = 1.0 Ω
Hint

Let I₁ (up through the 6.0 V branch) and I₃ (up through the 3.0 V branch) both flow into the top junction, so I₂ = I₁ + I₃ flows down through R₂. Write one loop equation for each cell.

Answer

Junction: I₂ = I₁ + I₃. Left loop: 6.0 = 2.0 I₁ + 4.0 I₂. Right loop: 3.0 = 1.0 I₃ + 4.0 I₂. Solving: I₁ = 1.29 A, I₃ = −0.43 A, I₂ = 0.86 A (6 ÷ 7 A) down through R₂. I₃ is negative, so 0.43 A flows down through the 3.0 V cell, into its positive terminal: the 6.0 V cell is pushing current backwards through the 3.0 V cell, which is being charged (it takes in energy rather than supplying it).

Step by step
  1. Junction rule at the top: I₁ + I₃ = I₂.
  2. Loop through the 6.0 V cell and R₂: 6.0 = 2.0 I₁ + 4.0 I₂.
  3. Loop through the 3.0 V cell and R₂: 3.0 = 1.0 I₃ + 4.0 I₂.
  4. Substitute I₂ = I₁ + I₃: 6.0 = 6.0 I₁ + 4.0 I₃ and 3.0 = 4.0 I₁ + 5.0 I₃.
  5. Solving: I₁ = 9 ÷ 7 = 1.29 A, I₃ = −3 ÷ 7 = −0.43 A, so I₂ = 6 ÷ 7 = 0.86 A.
  6. The minus sign means the current in the 3.0 V branch flows down, the opposite way to the one assumed: into the cell's positive terminal.
  7. So the 3.0 V cell is being charged by the 6.0 V cell: energy is going into it.
Full working
  1. I₂ = I₁ + I₃
  2. 6.0 = 2.0 I₁ + 4.0 I₂
  3. 3.0 = 1.0 I₃ + 4.0 I₂
  4. I₁ = 1.29 A, I₃ = −0.43 A
  5. I₂ = 0.86 A; 3.0 V cell charged
Question Two

Question Two

a
Achieved

A 470 μF capacitor in a camera flash circuit is charged to 12 V.

Use Q = CV.

Calculate the charge stored.

Hint

Change microfarads to farads: 1 μF = 1 × 10⁻⁶ F.

Answer

Q = 470 × 10⁻⁶ × 12 = 5.64 × 10⁻³ C.

Step by step
  1. C = 470 μF = 470 × 10⁻⁶ F.
  2. Q = CV = 470 × 10⁻⁶ × 12 = 5.64 × 10⁻³ C.
Full working
  1. Q = CV = 470 × 10⁻⁶ × 12
  2. Q = 5.64 × 10⁻³ C
b
Achieved

The 470 μF capacitor holds 5.64 × 10⁻³ C at 12 V.

Use E = ½QV.

Calculate the energy stored.

Hint

Half of charge times voltage.

Answer

E = ½ × 5.64 × 10⁻³ × 12 = 3.38 × 10⁻² J.

Step by step
  1. E = ½QV.
  2. E = 0.5 × 5.64 × 10⁻³ × 12 = 0.0338 J.
Full working
  1. E = ½QV = 0.5 × 5.64 × 10⁻³ × 12
  2. E = 3.38 × 10⁻² J
c
Merit

The 470 μF capacitor, charged to 12 V, discharges through a 10 kΩ resistor.

Use τ = RC and V = V₀e^(−t ÷ τ).

Calculate the time constant, the voltage after one time constant, and how long the voltage takes to fall to 3.0 V.

Hint

For the last part, take natural logs: ln(V₀ ÷ V) = t ÷ τ.

Answer

τ = 10 × 10³ × 470 × 10⁻⁶ = 4.7 s. After one time constant V = 12 × e⁻¹ = 4.4 V (37% of 12 V). 3.0 = 12e^(−t ÷ 4.7), so t = 4.7 × ln 4 = 6.5 s.

Step by step
  1. τ = RC = 10 × 10³ × 470 × 10⁻⁶ = 4.7 s.
  2. After one time constant: V = 12 × e⁻¹ = 12 × 0.368 = 4.4 V.
  3. For 3.0 V: 3.0 = 12 e^(−t ÷ 4.7), so e^(−t ÷ 4.7) = 0.25.
  4. t ÷ 4.7 = ln 4 = 1.386, so t = 6.5 s.
Full working
  1. τ = RC = 4.7 s
  2. V(τ) = 12e⁻¹ = 4.4 V
  3. 3.0 = 12e^(−t ÷ 4.7)
  4. t = 4.7 × ln 4 = 6.5 s
d
Excellence

Two square metal plates, 0.20 m by 0.20 m, are 1.0 mm apart in air. They are charged to 12 V, then disconnected from the battery. The plates are then pulled apart to 2.0 mm.

Use C = ε₀A ÷ d with ε₀ = 8.85 × 10⁻¹² F m⁻¹, Q = CV and E = ½CV².

Calculate the capacitance and stored energy before the plates are moved. Explain what happens to the charge, the voltage and the stored energy when the plates are pulled apart, and where any extra energy comes from.

Hint

Once the battery is disconnected the charge has nowhere to go.

Answer

C = 8.85 × 10⁻¹² × 0.040 ÷ 1.0 × 10⁻³ = 3.54 × 10⁻¹⁰ F (354 pF). Q = 3.54 × 10⁻¹⁰ × 12 = 4.25 × 10⁻⁹ C; E = ½ × 3.54 × 10⁻¹⁰ × 12² = 2.55 × 10⁻⁸ J. Disconnected, the charge cannot change: Q stays 4.25 × 10⁻⁹ C. Doubling d halves C to 1.77 × 10⁻¹⁰ F, so V = Q ÷ C doubles to 24 V. The energy E = ½QV doubles to 5.10 × 10⁻⁸ J. The extra 2.55 × 10⁻⁸ J is the work done pulling the plates apart: the oppositely charged plates attract, so a force is needed to separate them.

Step by step
  1. A = 0.20 × 0.20 = 0.040 m², d = 1.0 × 10⁻³ m.
  2. C = ε₀A ÷ d = 8.85 × 10⁻¹² × 0.040 ÷ 1.0 × 10⁻³ = 3.54 × 10⁻¹⁰ F.
  3. Q = CV = 3.54 × 10⁻¹⁰ × 12 = 4.25 × 10⁻⁹ C, and E = ½CV² = 0.5 × 3.54 × 10⁻¹⁰ × 144 = 2.55 × 10⁻⁸ J.
  4. Disconnected from the battery, the charge on the plates stays the same.
  5. Doubling the gap halves C (1.77 × 10⁻¹⁰ F), so V = Q ÷ C doubles to 24 V.
  6. E = ½QV: same Q, double V, so the energy doubles to 5.10 × 10⁻⁸ J.
  7. The plates have opposite charges and attract, so pulling them apart takes work: that work is the extra stored energy.
Full working
  1. C = 8.85 × 10⁻¹² × 0.040 ÷ 1.0 × 10⁻³ = 3.54 × 10⁻¹⁰ F
  2. E = ½ × 3.54 × 10⁻¹⁰ × 12² = 2.55 × 10⁻⁸ J
  3. Q constantC halves | V = 24 V
  4. E = 5.10 × 10⁻⁸ Jdoubles
  5. extra energy = work pulling the plates apart
Question Three

Question Three

a
Achieved

A phone charger's transformer steps 230 V mains down to 12 V. Its primary coil has 1150 turns.

Use Vs ÷ Vp = Ns ÷ Np.

Calculate the number of turns on the secondary coil.

Hint

The ratio of voltages equals the ratio of turns.

Answer

Ns = 1150 × 12 ÷ 230 = 60 turns.

Step by step
  1. Vs ÷ Vp = Ns ÷ Np, so Ns = Np × Vs ÷ Vp.
  2. Ns = 1150 × 12 ÷ 230 = 60 turns.
Full working
  1. Ns = Np × Vs ÷ Vp
  2. Ns = 1150 × 12 ÷ 230 = 60
b
Achieved

New Zealand's mains supply is 230 V rms at 50 Hz.

Use V_max = √2 × V_rms.

Calculate the peak voltage of the mains, and state how many times a second it reaches that peak in each direction.

Hint

rms is the peak divided by √2 for a sine wave.

Answer

V_max = √2 × 230 = 325 V. At 50 Hz it reaches +325 V 50 times a second (and −325 V 50 times a second).

Step by step
  1. V_max = √2 × V_rms = 1.414 × 230 = 325 V.
  2. 50 Hz means 50 complete cycles per second, each with one positive and one negative peak.
Full working
  1. V_max = √2 × 230 = 325 V
  2. 50 positive and 50 negative peaks per second
c
Merit

An electromagnet coil has an inductance of 0.30 H. When it is switched off, the current falls from 2.0 A to zero in 0.015 s.

Use ε = −L ΔI ÷ Δt.

Calculate the size of the EMF induced in the coil, and explain, using Lenz's law, why it can cause a spark at the switch.

Hint

Find ΔI ÷ Δt first. Which way does the induced EMF act, compared with the falling current?

Answer

ε = 0.30 × 2.0 ÷ 0.015 = 40 V. As the current falls, the coil's magnetic field collapses and the changing flux induces an EMF. By Lenz's law the induced EMF opposes the change: it acts to keep the current flowing in the same direction. A fast fall gives a large EMF, much larger than a supply of a few volts, and it appears across the opening switch contacts, so it can make the air between them conduct: a spark.

Step by step
  1. ΔI = 0 − 2.0 = −2.0 A in Δt = 0.015 s.
  2. ε = −L ΔI ÷ Δt = −0.30 × (−2.0) ÷ 0.015 = 40 V.
  3. The falling current means a collapsing magnetic field, so the flux through the coil changes and an EMF is induced.
  4. Lenz's law: the induced EMF opposes the change, so it tries to keep the current going.
  5. Because the current stops so quickly, the EMF is large and appears across the gap of the opening switch, which can spark.
Full working
  1. ΔI ÷ Δt = −2.0 ÷ 0.015 = −133 A s⁻¹
  2. ε = 0.30 × 133 = 40 V
  3. Lenz: EMF opposes the falltries to keep I flowing
  4. large EMF across the switch gapspark
d
Excellence

A 22 μF capacitor and a 120 Ω resistor are in series across the 230 V rms, 50 Hz mains.

Use X_C = 1 ÷ (2πfC), Z = √(R² + X_C²), V = IZ and tan φ = X_C ÷ R.

Calculate the rms current and the phase angle between the current and the supply voltage, and say whether the current leads or lags. Explain what happens to the current if the supply frequency is increased.

Hint

Find the capacitor's reactance first, then the impedance.

Answer

X_C = 1 ÷ (2π × 50 × 22 × 10⁻⁶) = 145 Ω. Z = √(120² + 145²) = 188 Ω. I = 230 ÷ 188 = 1.22 A. tan φ = 145 ÷ 120, so φ = 50.3°, with the current leading the voltage (in a capacitor the current leads the voltage by 90°, in the resistor they are in phase). At a higher frequency the capacitor charges and discharges more times per second, so it lets more current through: X_C = 1 ÷ (2πfC) falls, Z falls, and the current increases (and the phase angle gets smaller).

Step by step
  1. X_C = 1 ÷ (2πfC) = 1 ÷ (2π × 50 × 22 × 10⁻⁶) = 1 ÷ 0.00691 = 145 Ω.
  2. Z = √(R² + X_C²) = √(120² + 145²) = √35 300 = 188 Ω.
  3. I = V ÷ Z = 230 ÷ 188 = 1.22 A rms.
  4. tan φ = X_C ÷ R = 145 ÷ 120 = 1.21, so φ = 50.3°.
  5. In a capacitor the current leads the voltage, so in this circuit the current leads the supply voltage by 50.3°.
  6. Higher f: X_C = 1 ÷ (2πfC) gets smaller, so Z gets smaller and the current increases, with a smaller phase angle.
Full working
  1. X_C = 1 ÷ (2π × 50 × 22 × 10⁻⁶) = 145 Ω
  2. Z = √(120² + 145²) = 188 Ω
  3. I = 230 ÷ 188 = 1.22 A
  4. tan φ = 145 ÷ 120φ = 50.3°, current leads
  5. f up: X_C down, Z down, I up

All NCEA Level 3 Science

A Vertex Academy practice paper, written from NZQA's 2026 assessment specification for AS 91526. It is not an NZQA paper. Grades use the 2025 exam's cut scores: 7, 14 and 19 out of 24 for Achieved, Merit and Excellence.